As Miloh already mentioned, the 2-wire blinky LEDs are not just LEDs, but an analog circuit with built-in current limiter; <br>probably something even better than a resistor.<br>I'd expect the LEDs to turn on and start blinking at some voltage, then draw current that increases only very little, <br>
and finally get fried and fail as you turn up the voltage. I would guess that the LEDs can handle more than 5V. <br><br>Still greetings from Seoul, where I'm learining the concept of "love motel".<br><br>Christo^H^H^H^H^H^H^HFrantisek<br>
<br><div class="gmail_quote">On Tue, May 22, 2012 at 7:04 AM, jim <span dir="ltr"><<a href="mailto:jim@systemateka.com" target="_blank">jim@systemateka.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<br>
    Good advice! Thanks.<br>
    I believe that no LED works on less than<br>
1.5+ volts (1.7VDC comes to mind), and generally<br>
LEDs turn on at about 5mA and get brighter as<br>
the current increases until they fry. I believe<br>
they fry open not shorted and that any LED ought<br>
to take at least 20mA without frying.<br>
    If the things are scarce, get a lab supply<br>
that measures both voltage and current and start<br>
with 1.5V and see what the current is and judge<br>
the brightness; raise the voltage until 10mA<br>
current flows and judge the brightness; raise<br>
current to 15mA and judge; go as high as 20mA<br>
current and hope that's bright enough. 25mA is<br>
in the risky area.<br>
    Note that each LED may have a distinct ratio<br>
of current to brightness; if so, that argues for<br>
a separate current limiting resistor for each<br>
LED (or for the outlying cases).<br>
<div class="HOEnZb"><div class="h5"><br>
<br>
<br>
On Tue, 2012-05-22 at 04:20 +0900, Christoph Maier wrote:<br>
> Another Frantisek Apfelbeck impersonator here, hailing from Seoul:<br>
><br>
> For electrical purposes, these circuits are not LEDs, but integrated<br>
> two-terminal blinkylight integrated circuits.<br>
> As such, they have built-in current limiting and can be operated<br>
> directly off a battery.<br>
><br>
> As they apparently don't have a datasheet that is 1. not in Chinese<br>
> and 2. available,<br>
> it might make sense to sacrifice one or two of the LEDs by hooking<br>
> them up to a laboratory power supply that displays both voltage and<br>
> current,<br>
> then to ramp up the voltage from 1.0V in small increments until the<br>
> LEDs get fried, while measuring current and observing brightness.<br>
><br>
> If I recall correctly, Jimmie Rodgers gives away these blinky LEDs<br>
> with a battery [<a href="http://en.wikipedia.org/wiki/CR2032_battery" target="_blank">http://en.wikipedia.org/wiki/CR2032_battery</a>] when he<br>
> gives basic soldering instruction.<br>
><br>
> Greetings from Seoul,<br>
><br>
> ... Frantisek?<br>
><br>
> On Mon, May 21, 2012 at 11:48 PM, jim <<a href="mailto:jim@systemateka.com">jim@systemateka.com</a>> wrote:<br>
><br>
><br>
>            What kind of LEDs? Different types have differing<br>
>         voltage drops and current ranges.<br>
><br>
><br>
><br>
>         On Sun, 2012-05-20 at 22:16 -0700, Phil Spitler wrote:<br>
>         > Hi,<br>
>         > For simple LED projects, I usually use an online LED<br>
>         calculator to get<br>
>         > the values for the needed resistors.<br>
>         ><br>
>         ><br>
>         > I have just ordered some LEDs online but the specifications<br>
>         don't list<br>
>         > the forward voltage, just the current draw.<br>
>         ><br>
>         ><br>
>         > <a href="http://www.adafruit.com/products/679" target="_blank">http://www.adafruit.com/products/679</a><br>
>         ><br>
>         ><br>
>         > How would I figure out how to power the LEDs and what<br>
>         resistors to<br>
>         > use?<br>
>         ><br>
>         ><br>
>         > I am thinking of using 10 LEDs and having them all powered,<br>
>         all the<br>
>         > time.<br>
>         ><br>
>         ><br>
>         > I would love to know how to calculate my needs.<br>
>         ><br>
>         ><br>
>         > Any ideas?<br>
>         ><br>
>         ><br>
>         > Cheers.<br>
>         ><br>
>         ><br>
>         > Phil<br>
><br>
><br>
>         > Phil Spitler |   Associate Creative Director  |  Bonfire<br>
>         Labs |  t :<br>
>         > <a href="tel:415.394.8200" value="+14153948200">415.394.8200</a>  |  c : <a href="tel:415.571.3139" value="+14155713139">415.571.3139</a>  |  Bonfirelabs.com<br>
>         _______________________________________________<br>
>         Noisebridge-discuss mailing list<br>
>         <a href="mailto:Noisebridge-discuss@lists.noisebridge.net">Noisebridge-discuss@lists.noisebridge.net</a><br>
>         <a href="https://www.noisebridge.net/mailman/listinfo/noisebridge-discuss" target="_blank">https://www.noisebridge.net/mailman/listinfo/noisebridge-discuss</a><br>
><br>
><br>
><br>
><br>
<br>
<br>
</div></div></blockquote></div><br>