<div dir="ltr"><div>Ahh guys thank you so much for the ideas and vendor suggestions! Here's a schizophrenic list of what I've looked at thus far:</div><div><br></div><a href="http://www.pbclinear.com/Pages/AllProducts" target="_blank">http://www.pbclinear.com/Pages/AllProducts</a><br><div><br></div><div><a href="https://www.youtube.com/watch?v=uoimuJAi4EI" target="_blank">https://www.youtube.com/watch?v=uoimuJAi4EI</a><br></div><div><br></div><div><a href="https://www.youtube.com/watch?v=QDjUn1ZxcRU" target="_blank">https://www.youtube.com/watch?v=QDjUn1ZxcRU</a><br></div><div><br></div><div><a href="http://openbuildspartstore.com/" target="_blank">http://openbuildspartstore.com/</a><br></div><div><br></div><div><a href="https://www.1000bulbs.com/product/112763/GROW-710180.html" target="_blank">https://www.1000bulbs.com/product/112763/GROW-710180.html</a><br></div><div><br></div><div><a href="http://www.alibaba.com/product-detail/PMI-Square-Linear-Bearing-Block-Guide_1108536250.html" target="_blank">http://www.alibaba.com/product-detail/PMI-Square-Linear-Bearing-Block-Guide_1108536250.html</a><br></div><div><br></div><div><a href="http://www.unistrut.us/index.php?WP=show&GRP=Trolley" target="_blank">http://www.unistrut.us/index.php?WP=show&GRP=Trolley</a><br></div><div><br></div><div><a href="http://www.monsterguts.com/store/product.php?productid=17685" target="_blank">http://www.monsterguts.com/store/product.php?productid=17685</a><br></div><div><br></div><div>The main things I've come away with thus far:</div><div><ul><li>A windshield washer motor is a good lifting mechanism as it contains a worm gear which provides an inherent measure of safety, i.e. the cable won't move unless the motor moves it.<br></li><li>Many linear bearing slides are NOT meant to handle vertical loads.</li><li>A single pipe-like rail probably won't steady the torque of a potentially large lateral load like a bike if not perfectly centered regarding the rail.</li><li>Nearly all the low-profile solutions I've seen are insanely expensive.</li></ul>This guy though: <a href="https://www.youtube.com/watch?v=QDjUn1ZxcRU" target="_blank">https://www.youtube.com/watch?v=QDjUn1ZxcRU</a></div><div><br></div><div>That looks to be exactly what I prefer - the rail is low-profile and already has mounting holes. Since this project doesn't need to support much weight I imagine this type of rail is ok.</div><div><br></div><div>My next quandary is whether to use a belt (what minimum width will support the weight?) or a cable/rope. For a cable I'll have to install a roller to line it up with the track as the cable spirals out within the pulley. For a belt I'll have an additional line going to the slide platform but everything will be intrinsically aligned and easier to build. Hmmm.</div><div><br></div><div>I very much like the idea of the garage door opener but it's gonna be way too big for the areas i'm putting this in - essentially a stairwell.</div><div><br></div><div>For the motor control I'm imagining</div><div><ul><li>a simple MCU connected to a fat third-party motor driver or h-bridge with a current-sense resistor to detect stalls<br></li><li>Optical limit switches like hyah: <a href="http://www.goldmine-elec-products.com/prodinfo.asp?number=G20375B">http://www.goldmine-elec-products.com/prodinfo.asp?number=G20375B</a></li><li><a href="http://www.seeedstudio.com/depot/BoosterB24V2A5Brushed-DC-Motor-ControllerDual-Hbridge-p-2259.html">http://www.seeedstudio.com/depot/BoosterB24V2A5Brushed-DC-Motor-ControllerDual-Hbridge-p-2259.html<br></a></li><li><a href="http://www.seeedstudio.com/depot/BoosterB24V2A5Brushed-DC-Motor-ControllerDual-Hbridge-p-2259.html">http://www.newegg.com/Product/Product.aspx?Item=9SIA5FB1XG6349<br></a></li><li>There are R/C electronic speed controllers too which are ubiquitous and cheap - all you need to do is drive them with an MCU emulating the servo-position protocol.</li></ul></div><div>This email is long and I'm hungry, bye for now!</div><div><br></div><div>=]</div><div class="gmail_extra"><br clear="all"><div><div>--<br>Anders Nelson<br><br>+1 (517) 775-6129<br><br><a href="http://www.erogear.com" target="_blank">www.erogear.com</a></div></div>
<br><div class="gmail_quote">On Tue, May 19, 2015 at 4:17 PM, Anders Nelson <span dir="ltr"><<a href="mailto:anders.k.nelson@gmail.com" target="_blank">anders.k.nelson@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex"><div dir="ltr">Dear smart people, I want to make something.<div><br></div><div>I have really high ceilings in my flat and I'd like to store/display my and my roommates' bikes vertically along the wall. I need to have them raised up above the floor higher than anyone can reach though if this is to be useful.</div><div><br></div><div>So I'd like to make a motorized system where I can hook my front tire on a relatively standard tire hook, press a button and have the bike winched up along a track to arrive high on the wall near the ceiling.</div><div><br></div><div>Does anyone know of supplier(s) for ball-bearing tracks along which I can bolt a bicycle storage hook? Next, is there a good solution for a quiet, >50lb winch or gearhead motor you know of?</div><div><br></div><div>I've just started looking for parts, surplus is fine as is new stuff.</div><div><br></div><div>Any help is appreciated!</div><div><br clear="all"><div><div>--<br>Anders Nelson<br><br>+1 (517) 775-6129<br><br><a href="http://www.erogear.com" target="_blank">www.erogear.com</a></div></div>
</div></div>
</blockquote></div><br></div></div>