<div dir="ltr">we need a duct fan<br><br></div><div class="gmail_extra"><br><div class="gmail_quote">On Thu, Sep 22, 2016 at 8:50 PM, Jake <span dir="ltr"><<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">that's hilarious, i guess it would be perfect for what Trent wants to do.<br>
<br>
make sure you get plenty of ventilation, i should have mentioned.<br>
<br>
This can't be done in sudoroom without running a fan to the ventilation duct near the laser cutter.  Perhaps the clear acrylic flow-hood could be connected to a ventilation blower to the exhaust duct.<span class="HOEnZb"><font color="#888888"><br>
<br>
-jake</font></span><div class="HOEnZb"><div class="h5"><br>
<br>
On Thu, 22 Sep 2016, robb wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
i just found a 10.5" X 20" electric hotplate yesterday.<br>
it's on the projects shelves past the robot arm w/a note about component<br>
removal use on it.<br>
<br>
On Thu, Sep 22, 2016 at 3:39 PM, Trent Robbins <<a href="mailto:robbintt@gmail.com" target="_blank">robbintt@gmail.com</a>> wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Thanks Jake! I was planning on doing it by hand, but it would be neat to<br>
try the mechanical one at sudo room.<br>
<br>
Trent<br>
<br>
On Thursday, September 22, 2016, Jake <<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>> wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
a hotplate covered with clean sand heated up to 400 degrees (celsius)<br>
will be a surface on which you can place a circuitboard covered with such<br>
switches, and then you can pluck them out of the board as their solder<br>
melts.  This is how old boards had their parts salvaged from them back when<br>
people still did that.<br>
<br>
if you don't have the right hotplate and you want to use a skillet<br>
instead, you'll likely have to cut the circuitboard in half or thirds so<br>
that it will be small enough to fit in the skillet of sand.  no big deal.<br>
<br>
you could also remove them one at a time, using a desoldering tool.<br>
There's a motorized one at sudoroom, which is basically a gun-shaped<br>
soldering iron with a hollow tip and a foot-pedal activated vacuum pump.<br>
You could use that to pull the solder out of the hole for one of the two<br>
pins of each key, and then use a regular soldering iron to heat up the<br>
second one while pulling the key out with the other hand.<br>
<br>
good luck,<br>
-jake<br>
<br>
On Tue, 20 Sep 2016, Trent Robbins wrote:<br>
<br>
Does anyone know a good way to salvage from 101-105 mx brown keyboard<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
switches?<br>
<br>
I'm planning on building my own keyboard this fall or winter and have<br>
plenty of time to source scrap.<br>
<br>
<a href="http://cubiq.org/build-your-very-own-pc-keyboard" rel="noreferrer" target="_blank">http://cubiq.org/build-your-ve<wbr>ry-own-pc-keyboard</a><br>
<br>
Build process is as complex as you'd expect.<br>
<br>
Teensy firmware: <a href="https://github.com/tmk/tmk_keyboard" rel="noreferrer" target="_blank">https://github.com/tmk/tmk_key<wbr>board</a><br>
<br>
<br>
<br>
Trent<br>
<br>
<br>
</blockquote></blockquote>
<br>
--<br>
(Sent from cellphone)<br>
<br>
______________________________<wbr>_________________<br>
sudo-discuss mailing list<br>
<a href="mailto:sudo-discuss@lists.sudoroom.org" target="_blank">sudo-discuss@lists.sudoroom.or<wbr>g</a><br>
<a href="https://sudoroom.org/lists/listinfo/sudo-discuss" rel="noreferrer" target="_blank">https://sudoroom.org/lists/lis<wbr>tinfo/sudo-discuss</a><br>
<br>
<br>
</blockquote>
<br>
</blockquote>
</div></div></blockquote></div><br></div>