<div dir="ltr"><div>i just found a 10.5" X 20" electric hotplate yesterday.<br></div>it's on the projects shelves past the robot arm w/a note about component removal use on it. <br><div><div><div class="gmail_extra"><br><div class="gmail_quote">On Thu, Sep 22, 2016 at 3:39 PM, Trent Robbins <span dir="ltr"><<a href="mailto:robbintt@gmail.com" target="_blank">robbintt@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Thanks Jake! I was planning on doing it by hand, but it would be neat to try the mechanical one at sudo room.<div><br></div><div>Trent<span class=""><br><br>On Thursday, September 22, 2016, Jake <<a href="mailto:jake@spaz.org" target="_blank">jake@spaz.org</a>> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">a hotplate covered with clean sand heated up to 400 degrees (celsius) will be a surface on which you can place a circuitboard covered with such switches, and then you can pluck them out of the board as their solder melts.  This is how old boards had their parts salvaged from them back when people still did that.<br>
<br>
if you don't have the right hotplate and you want to use a skillet instead, you'll likely have to cut the circuitboard in half or thirds so that it will be small enough to fit in the skillet of sand.  no big deal.<br>
<br>
you could also remove them one at a time, using a desoldering tool. There's a motorized one at sudoroom, which is basically a gun-shaped soldering iron with a hollow tip and a foot-pedal activated vacuum pump. You could use that to pull the solder out of the hole for one of the two pins of each key, and then use a regular soldering iron to heat up the second one while pulling the key out with the other hand.<br>
<br>
good luck,<br>
-jake<br>
<br>
On Tue, 20 Sep 2016, Trent Robbins wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Does anyone know a good way to salvage from 101-105 mx brown keyboard<br>
switches?<br>
<br>
I'm planning on building my own keyboard this fall or winter and have<br>
plenty of time to source scrap.<br>
<br>
<a href="http://cubiq.org/build-your-very-own-pc-keyboard" target="_blank">http://cubiq.org/build-your-ve<wbr>ry-own-pc-keyboard</a><br>
<br>
Build process is as complex as you'd expect.<br>
<br>
Teensy firmware: <a href="https://github.com/tmk/tmk_keyboard" target="_blank">https://github.com/tmk/tmk_key<wbr>board</a><br>
<br>
<br>
<br>
Trent<br>
<br>
</blockquote>
</blockquote></span></div><span class="HOEnZb"><font color="#888888"><br><br>-- <br>(Sent from cellphone)<br>
</font></span><br>______________________________<wbr>_________________<br>
sudo-discuss mailing list<br>
<a href="mailto:sudo-discuss@lists.sudoroom.org">sudo-discuss@lists.sudoroom.<wbr>org</a><br>
<a href="https://sudoroom.org/lists/listinfo/sudo-discuss" rel="noreferrer" target="_blank">https://sudoroom.org/lists/<wbr>listinfo/sudo-discuss</a><br>
<br></blockquote></div><br></div></div></div></div>