[Build] Plumbing Update

Kelly hurtstotouchfire at gmail.com
Sat Feb 27 00:25:46 UTC 2010

I have no plans this evening, and could be by around 1900, so ping me
if you guys can use some help this evening with unskilled work or


On Fri, Feb 26, 2010 at 12:37, Jeffrey Malone <ieatlint at tehinterweb.com> wrote:
> Hey all..
> Scott and Zedd did an impressive amount of work Thursday on the
> plumbing for the kitchen and new bathroom.
> In doing so, most of Thursday saw no water in the space (so no
> bathroom working at all).
> Unfortunately, despite them working for over twelve hours, the
> plumbing is at present not done.  Only the original toilet is
> currently working -- we at present have no sink.
> I repeat, Noisebridge at time of writing has NO SINK at all.  Not in
> the bathroom, not in the kitchen.  The toilet works.  Yes, sorry for
> the unsanitary condition this is in.  It is very temporary.
> The drains for both sinks should be working (although the kitchen sink
> drain is untested), for whatever help that is.
> There is a lot of new visible copper piping going around, including a
> ball switch that is on the bathroom wall.  Obviously you shouldn't
> move that switch (which is currently off, but water runs to it), as
> leaks are currently present in the other pipes.
> What needs to be done to get the sinks working in the space with cold water:
> Both sinks:
> There are a number of leaks in the truly crappy soldering job that I
> can proudly take blame in -- these need to be found and fixed.
> Bathroom sink:
> There is a shunt going through the bathroom wall that is capped off.
> The cap needs to be removed, and the sink connected to it.
> Kitchen sink:
> The pressure seal valve connected to the sinks faucets appeared to be
> leaking.  This will need to be reseated properly.
> The hoses for the faucets need to be attached to the pressure seal valve.
> Overall, it's small amount of work.  However, for hot water, there is
> still a bit to be done, including running much of the pipe and
> electricity to the heater itself.
> I believe either Zedd or Scott will be around today (or "early"
> tomorrow) to get the cold water running, so we will have sinks to wash
> hands/dishes.
> Either way, we should all really thank both of them, as they really
> put in much more than a full day yesterday and made a lot of progress
> on some really not fun work.
> Jeffrey
> Oh, and a couple other notes...
> This is for reference now and in the future:
> Our water shut off valve is in the basement.  There's a "room" in
> there with walls of hardware cloth (south end, just follow the south
> wall from the elevator and you'll run into it).  There are two valves
> somewhat in the middle of the room, above your head (~10ft up).  One
> has a red rag near it, the other a white.  Ours is the one with the
> white rag, the second floor is red.
> Turning this valve off will shut down water to just our floor.  If a
> leak occurs to the toilet of the original bathroom, or before the
> valve installed at shoulder height in the ADA bathroom, you need to
> shut this off.  Any leaks on the other side of that (including to the
> sink in the original bathroom) should not use the valve in the
> basement, but the shutoff valve in the ADA compliant bathroom.
> At time of writing, the basement valve is half on (in order to test
> our soldering without quite as much water spraying) -- this should be
> fixed when work on the plumbing resumes.  The valve in the ADA
> compliant bathroom is off and SHOULD NOT BE TURNED ON, lest you want
> to see a lot of water spray around, and have some very pissed off
> people.
> _______________________________________________
> Build mailing list
> Build at lists.noisebridge.net
> https://www.noisebridge.net/mailman/listinfo/build

More information about the Build mailing list