[Noisebridge-discuss] Floor in the rear
jim
jim at well.com
Fri Jun 11 23:24:29 UTC 2010
well, yes. the drum sander does a much better job
(more effective per sweat drop) than an orbital
sander. but all floor sanders kick up some dust. i
just finished using an orbital sander (done last
tuesday), and was happy about the small amount of
dust. i wasn't happy about the swirl marks on the
wood but learned a lesson: pivot on the rear wheels
when turning it.
looks like wednesday AM for me and the sander.
On Fri, 2010-06-11 at 15:48 -0700, Lamont Lucas wrote:
> Just my two cents, having sanded quite a bit of noisebridge floor, but
> in my experience the standup drum sander was way easier to use, quicker
> and much cleaner than the orbital sander. I rented them from Hertz on
> mission between 16th and 17th (and generally wheeled the sander on the
> street rather than with a car). The orbital sander did a terrible job
> cleaning up after itself and threw sawdust (and later, putty dust)
> everywhere. The drum sander still threw up some, but most of it went
> into the bag. Hertz ran weekend specials for I think about $90.
>
> One of my pet peeves when doing the floor the first time was when people
> made suggestions but were not motivated to help. I realize this is the
> exact same situation, and I hope you're not as irritated by me as I was
> by some of the suggestions I received. I just didn't want you to be
> horrified by the amount of sawdust thrown around.
>
> Rachel McConnell wrote:
> > Having discussed this with Jim, he has convinced me that some sanding
> > will be required or the paint will come up. His recommendation is to
> > rent an orbital sander, which apparently has a kind of included vaccuum
> > cleaner so that the dust doesn't go All Over. Jim has kindly
> > volunteered to do the sanding early or mid next week, assuming a good
> > mopping can be done before hand.
> >
> > I plan to mop on Saturday sometime unless someone else REALLY WANTS TO
> > in which case go right ahead. Jim recommends trisodium phosphate and
> > bleach and maybe a little dish soap.
> >
> > After sanding, there will still need to be some puttying, and then
> > painting. Also there is still some patch work needed (I ran out of
> > nails) which I'll try to kick out on Saturday too.
> >
> > Rachel
> >
> > Rachel McConnell wrote:
> >
> >> At Erin's exceptional work party yesterday, a bunch of us attacked the
> >> floor at the back of the space, that area that was partly covered in
> >> rotting plywood and linoleum. We tore all that up! The floor
> >> underneath was not in such bad shape as we feared, but did need repair
> >> in several areas. I do not think it is worth the disruption to regular
> >> Noisebridge operations to do the full sanding/refinishing that we did on
> >> the rest of the floor, which despite its beautiful results was arduous
> >> and timeconsuming and made a ton of dust and fumes. My plan is this:
> >>
> >> 1. patch with flooring
> >> 2. clean
> >> 3. putty
> >> 4. paint
> >>
> >> There were only three areas that needed significant patching with
> >> replacement floorboards. We got a lot of the patching done yesterday;
> >> there's a big area by the bathroom that still requires work. Initial
> >> sweeping and vaccuuming has also been done but more is needed,
> >> especially as the floorboard patching generates sawdust.
> >>
> >> WANT TO HELP?
> >>
> >> These are the next tasks, which can be done to some degree in parallel.
> >> Pick any that you feel confident of doing:
> >>
> >> * clean the bathroom! We had to take the door off the hinges for a bit
> >> and a lot of dust and mess got in, which I didn't notice until I was
> >> about to leave and had no more effort left to clean up.
> >>
> >> * move more Stuff off of this part of the floor. There are some rolling
> >> metal shelves and some beams that weren't yet in our way that we haven't
> >> relocated yet. Mostly stuff is in the rear classroom; that's not usable
> >> now so might as well put the rest in there.
> >>
> >> * patch the floor! There are more reclaimed floorboards in the south
> >> stairwell. Nails are in the new bathroom, hammers & saws in the shop.
> >> If you're not familiar with the tongue-and-groove joins that these
> >> boards have, either research it or do a different job.
> >>
> >> * sweep and/or vaccuum. Concentrate on the end away from the bathroom
> >> as the repairing there will generate more sawdust. Once an area is
> >> pretty dust-free it can be puttied!
> >>
> >> * putty the gaps! There are three one-gallon containers of putty just
> >> by the kitchen in the central walkway. Putty knives in the workshop.
> >> Mark the wet areas with tape or something when you're done so people
> >> know not to step there. (Hint: Start in the corners and work out.)
> >>
> >> I'll be back Monday evening to continue with this work. If you are
> >> interested in helping but would like more direction than the above,
> >> please show up and I will absolutely tell you exactly what to do!
> >>
> >> Many thanks to the people who have worked on this so far (I am sure I am
> >> leaving someone out, sorry): Scott, Matt H, Erin, BJ, Sai, Chris L,
> >> Xander, mct, and a couple people whose names I did not catch.
> >>
> >> Rachel
> >> _______________________________________________
> >> Noisebridge-discuss mailing list
> >> Noisebridge-discuss at lists.noisebridge.net
> >> https://www.noisebridge.net/mailman/listinfo/noisebridge-discuss
> >>
> > _______________________________________________
> > Noisebridge-discuss mailing list
> > Noisebridge-discuss at lists.noisebridge.net
> > https://www.noisebridge.net/mailman/listinfo/noisebridge-discuss
> >
> >
> >
>
> _______________________________________________
> Noisebridge-discuss mailing list
> Noisebridge-discuss at lists.noisebridge.net
> https://www.noisebridge.net/mailman/listinfo/noisebridge-discuss
>
More information about the Noisebridge-discuss
mailing list